STANDARD C520 - Keypad Guide |----------------------------------------------------------------------------| |Key | Alone | With "FUNC" key | Key alone in set |In Set With "F" | |----------------------------------------------------------------------------| | 0 | 0 |Enter Set Mode |Mute keypad bleep |Set Band Edge Limit| | | | | |xyzt:VHF 1xy to 1zt| | 1 | 1 |PTT Lock |- |Tx DelayON repeater| | | | | | | | 2 | 2 |Dual Watch. In Mem o|1kHz entry on keypad|Match CTCSS on scan| | | |scanMem: VFO,FUNC+2 | | | | 3 | 3 |Output Power L/M/H |- |Switch UHF Bands | | | | | | | | 4 | 4 |Frequency Lock |Mute noise while sql|Input 4 or 3 digits| | | | | | | | 5 | 5 |Battery Saver |Auto power off 30min|- | | | | | | | | 6 | 6 |Select Step Size |Enable tune in lock |Fast tune 1MHz/100k| | | | | | | | 7 | 7 |CTCSS select TX/RX |CTCSS tone frequency|- | | | | | | | | 8 | 8 |Repeater Shift +/- |Set shift freq, over|Cross Band Repeater| | | | |10MHz set with tune | | | 9 | 9 |Reverse Repeat Shift|Make LAMP button REV|Up/Dn keys do 10MHz| | | | | | | | * |Step Down|Search up, then 0 if| | | | | |Busy or Pause scan | | | | # |Step Up |Memory Shift | | | | | | | | | | A |Cancel | | | | | | | | | | | B |Pager On |Set Pager Codes | | | | | | | | | | C |Mem Scan |Partial Memory Scan,| | | | | |only M°: VFO,Func+C | | | | D |Dial/Mem |Store Dial In Memory| | | | | | | | | |Lamp|auto 5sec|light on/off | | | | | | | | | |Sqlc|set squlc| | | | | | | | | | |Call|1750 Hz | | | | | | | | | | |Rst |reset all| | | | | | | | | | |Tune|up/down |up/down 100/1000 kHz| | | |----------------------------------------------------------------------------| |To add 820-900,900-980 band in UHF: UHF F+L F+0 F+B F+L F+3 A | |----------------------------------------------------------------------------| |Scan between 2 memory Mx and My: Mem mode, FUNC * when Mx, then press y (My)| |----------------------------------------------------------------------------| |To remove frequency from memory: [n°mem]+A A | |----------------------------------------------------------------------------| |SET +/- indipendent RX/TX freq. in memory number [n°mem] | |- In VFO mode it fixes RX freq: F+D [n°mem] | |- In VFO mode it fixes TX freq: F+D F+A [n°mem] | |----------------------------------------------------------------------------| |ACTIVATE +/- indipendend RX/TX freq. in mem: F+D F+[n°mem] (it appears +/-) | |DISABLE +/- indipendend RX/TX freq. in memory number [n°mem] | |- delete n°mem: [n°mem]+A A | |- set new freq. in n°mem'; set new freq. in n°mem | |- delete n°mem' if unwanted | |----------------------------------------------------------------------------| Writed by: NICOLA IV3WHU - JN65TS - 14 Feb 2002 Address: P.O.BOX 3717 - 34011 AURISINA TS - ITALY Email: iv3whu**NOSPAM**@amsat.org - Web: www.qsl.net/iv3whu Packet: IV3WHU**NOSPAM**@IR3IP.AMPR.ORG HamBBS Mail: IV3WHU@IK3GET.IVEN.ITA.EU [Correct view]: use fixed sized font (example: Lucida Console 10). -END-