Msg Nr. : 32356 Da : LU7AKC Per : NET9K6@WW Tipo/status : B$ Data/ora : 0815/0117 Dimensione : 5778 Titolo : IC3220 & 9600 Bps Bid (Mid) : 12256_LU7AKC How to iface Ic-3220 & G3RUH Hi everybody, The following instructions tells you how to make the right connections to an ICOM IC-3220 in order to be connected to the G3RUH 9600 bauds modem. ------------------------------- WARNING !! ------------------------------------- The following steps are not very dificult to follow, but are to be carried by a person with a minimum experience in electronic radio equipment. If you are not such a person, ask to a friend with the required knowledge to do the job for you. Otherwise, permanent damage to your rig can result.! Also, (evidently), this manipulation will invalidate the rig warranty, so perhaps you prefer to wait till the end of its validation period... The author of this note is in no way responsible for any damage that can be caused to your equipment by doing this modification to it. Do it at your own risk, and think twice before begin ! -------------------------------------------------------------------------------- Modification instructions ------------------------- (n) = Number of screws. Material required: Screwdriver, Solder Iron, Coax cable (see text) 1 - Remove (4) the BOTTOM cover. (the one without the speaker). 2 - Remove (4+2) the shielding plate covering the P.A. output module. 3 - Remove (2) and discard the bottom small plate covering the hole behind the antenna coaxial cable. Restore the two screws in place, just to store it for the future. 4 - Locate connector J2 (The white big one, near to front panel) which is used to interface the two main boards. (16 pins). 5 - Locate pins 1, 2, and 15 of J2. Pin 1 is the nearest to the box side of the rig. Pin 15 (the one before last) is located about the middle of the main board. Pin description: 1 - UHF TX stage modulator voltage input. 2 - Ground. 15 - UHF RX detector output. If in doubt about pinout, see schematic diagram (Main B unit, left hand) 6 - Take two pieces of SMALL diameter coaxial cable, (Z:50 ohms preferred by me, but ordinary AF coax cable will perform pretty well). Aproximate diameter MUST be no more then 4 mm, and lenght as required. Following Murphy's law be generous ... 7 - Join the two (outer) shield parts of coax cables and solder them to pin 2 (ground) at the upper (visible) part of J2. Solder the inner (active) part of one cable to pin 1 and the other to pin 15. Soldering should be performed to the upper part of J2 with EXTREME CAUTION, as the plastic support structure of J2 connector, can be seriously damaged !!!. 8 - Route the two cables trough the main board, up to the hole near the antenna cable, routing them in such a way, that traverses the small square hole at the bottom part of the plate covering the final P.A. 9 - Secure the cables at the output hole with a BIG plastic strap. 10 - Reinstall (6) the cover of final P.A. 11 - Reinstall (4) the bottom cover of the rig. 12 - Solder appropiate connectors at the other end of coax cables. End of installation. --------------------------------------------------------------------- Notes: With this modification, only the UHF part of the rig is affected, i.e. the mod will only work for the 432 Mc/s. band. Also, some noise has been observed at RX detector output line, which make the DCD led of the TNC blink, but this does not affect the overall performance of the assembly. As a guide, using the french TPK program, a serial (rs232) speed of 19200 bds, the well known G3RUH modem, and a standard TNC, a file of 1.5 Mbytes has been transmited in one hour, obtaining and average speed of 364 cps. (TPK measured). 73's QRO of Andreu. EA3CQY @ EA3MM Barcelona.Catalunya.Spain Msg Nr. : 51363 Da : IW4DGM Per : ICOM @ITA Tipo/status : BF Data/ora : 1012/2256 Dimensione : 4354 Titolo : IC3220 9600bds modifica Bid (Mid) : 3609_IW4CEA Modifica solo per la banda UHF del IC-3220 con il Modem G3RUH a 9600 bds. ------------------------------- ATTENZIONE ------------------------------------ La seguente modifica non e' difficile da eseguire ma deve essere effettuata da una persona con un minimo di esperienza in lavori su apparecchiature elettroniche. Se non siete fra questi, chiedete ad un amico di provata esperienza di fare il lavoro per voi. Altrimenti e' possibile che voi causiate danni permanenti al vostro apparato! Comunque e' chiaro che la modifica invalida la garanzia dell'apparato, per cui forse preferite aspettare il termine del periodo di garanzia... L'autore (ed il traduttore) di questa nota non e' in nessun modo responsabile per qualsiasi danno che puo' essere causato al vostro apparato a causa di questa modifica. Lo fate a vostro rischio, e pensateci due volte prima di cominciare ! (Nota del traduttore: Che menagramo questo spagnolo!) -------------------------------------------------------------------------------- Istruzioni per la Modifica -------------------------- 1 - Rimuovere le 4 viti del coperchio INFERIORE. (quello senza altoparlante). 2 - Rimuovere le 4+2 viti della schermatura che copre il modulo P.A. 3 - Rimuovere le 2 viti e togliere la piastrina metallica che copre il foro sotto al cavo coassiale d'antenna. Riavvitare provvisoriamente le 2 viti. 4 - Localizzare il connettore J2 (l'unico bianco grande, vicino al pannello frontale) usato per interfacciare le due schede principali. (16 pins). 5 - Localizzare i pins 1, 2, e 15 di J2. Il pin 1 e' quello piu' vicino al lato del contenitore dell'apparato. Il pin 15 (il penultimo) e' circa a meta' della scheda. Descrizione dei pin: 1 - Entrata modulatore TX UHF. 2 - Massa. 15 - Uscita discriminatore RX UHF. Se non siete sicuri della funzione dei pin, controllare lo schema elettrico (Main B unit, lato sinistro) 6 - Prendete due cavetti schermati SOTTILI, (io ho scelto cavetti a 50 ohms, ma vanno benissimo normali cavetti per AF). Il diametro DEVE essere non piu' di 4 mm. 7 - Unite le due calze dei cavetti e saldatele al pin 2 (massa) sulla parte superiore visibile di J2. Saldate il centrale di un cavetto al pin 1 e il centrale dell'altro al pin 15. La saldatura sulla parte superiore di J2 deve essere fatta con ESTREMA CAUTELA, dato che il supporto di plastica del connettore J2, puo' essere danneggiato seriamente !!! 8 - Far passare i due cavetti lungo la scheda fino al foro vicino al cavo d'antenna, in modo poi da farli attraversare il piccolo foro quadrato nella parte inferiore del coperchio metallico del finale P.A. 9 - Fermare i cavetti, fatti uscire dal foro, con una grossa fascietta di plastica. 10 - Riavvitare le 6 viti al coperchio del finale P.A. 11 - Riavvitare le 4 viti del coperchio inferiore dell'apparato. 12 - Saldare i connettori adatti all'altro lato dei cavetti coassiali. Fine dell'istallazione. ----------------------------------------------------------------------- Nota: Questa modifica riguarda SOLO la parte UHF dell'apparato, quindi la modifica funziona solo per la banda dei 432 MHz. E' stato riscontrato un certo livello di rumore in uscita al discriminatore RX, per cui il led DCD del TNC tende a lampeggiare, ma cio' non pregiudica in nessun modo le prestazioni operative. Giusto come paragone, usando il prg TPK, velocita' della seriale (rs232) a 19200 bds, il ben conosciuto Modem G3RUH ed un TNC standard, in un'ora e' stato stato trasmesso un file di 1.5 Mbytes, alla velocita' di 364 cps. (indicazione del TPK). Andreu EA3CQY @EA3MM Barcellona.Catalogna.Spagna -------------------------------------- traduzione di questa mezza modifica di ÚÄÄ ex ÄÄ¿ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ ³ iw4bkk ³³ PAOLO in Ravenna IW4DGM @IW4CEA.ITA.EU ³Ü ÀÄÄÄÄÄÄÄÄÙÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙÛ ßßßßßßßßßßßßßßßßßßßßßßßßßßßßßßßßßßßßßßßßßßßßßßßßßß Msg Nr. : 32356 Da : LU7AKC Per : NET9K6@WW Tipo/status : B$ Data/ora : 0815/0117 Dimensione : 5778 Titolo : IC3220 & 9600 Bps Bid (Mid) : 12256_LU7AKC How to iface Ic-3220 & G3RUH Hi everybody, The following instructions tells you how to make the right connections to an ICOM IC-3220 in order to be connected to the G3RUH 9600 bauds modem. ------------------------------- WARNING !! ------------------------------------- The following steps are not very dificult to follow, but are to be carried by a person with a minimum experience in electronic radio equipment. If you are not such a person, ask to a friend with the required knowledge to do the job for you. Otherwise, permanent damage to your rig can result.! Also, (evidently), this manipulation will invalidate the rig warranty, so perhaps you prefer to wait till the end of its validation period... The author of this note is in no way responsible for any damage that can be caused to your equipment by doing this modification to it. Do it at your own risk, and think twice before begin ! -------------------------------------------------------------------------------- Modification instructions ------------------------- (n) = Number of screws. Material required: Screwdriver, Solder Iron, Coax cable (see text) 1 - Remove (4) the BOTTOM cover. (the one without the speaker). 2 - Remove (4+2) the shielding plate covering the P.A. output module. 3 - Remove (2) and discard the bottom small plate covering the hole behind the antenna coaxial cable. Restore the two screws in place, just to store it for the future. 4 - Locate connector J2 (The white big one, near to front panel) which is used to interface the two main boards. (16 pins). 5 - Locate pins 1, 2, and 15 of J2. Pin 1 is the nearest to the box side of the rig. Pin 15 (the one before last) is located about the middle of the main board. Pin description: 1 - UHF TX stage modulator voltage input. 2 - Ground. 15 - UHF RX detector output. If in doubt about pinout, see schematic diagram (Main B unit, left hand) 6 - Take two pieces of SMALL diameter coaxial cable, (Z:50 ohms preferred by me, but ordinary AF coax cable will perform pretty well). Aproximate diameter MUST be no more then 4 mm, and lenght as required. Following Murphy's law be generous ... 7 - Join the two (outer) shield parts of coax cables and solder them to pin 2 (ground) at the upper (visible) part of J2. Solder the inner (active) part of one cable to pin 1 and the other to pin 15. Soldering should be performed to the upper part of J2 with EXTREME CAUTION, as the plastic support structure of J2 connector, can be seriously damaged !!!. 8 - Route the two cables trough the main board, up to the hole near the antenna cable, routing them in such a way, that traverses the small square hole at the bottom part of the plate covering the final P.A. 9 - Secure the cables at the output hole with a BIG plastic strap. 10 - Reinstall (6) the cover of final P.A. 11 - Reinstall (4) the bottom cover of the rig. 12 - Solder appropiate connectors at the other end of coax cables. End of installation. --------------------------------------------------------------------- Notes: With this modification, only the UHF part of the rig is affected, i.e. the mod will only work for the 432 Mc/s. band. Also, some noise has been observed at RX detector output line, which make the DCD led of the TNC blink, but this does not affect the overall performance of the assembly. As a guide, using the french TPK program, a serial (rs232) speed of 19200 bds, the well known G3RUH modem, and a standard TNC, a file of 1.5 Mbytes has been transmited in one hour, obtaining and average speed of 364 cps. (TPK measured). 73's QRO of Andreu. EA3CQY @ EA3MM Barcelona.Catalunya.Spain Msg Nr. : 51363 Da : IW4DGM Per : ICOM @ITA Tipo/status : BF Data/ora : 1012/2256 Dimensione : 4354 Titolo : IC3220 9600bds modifica Bid (Mid) : 3609_IW4CEA Modifica solo per la banda UHF del IC-3220 con il Modem G3RUH a 9600 bds. ------------------------------- ATTENZIONE ------------------------------------ La seguente modifica non e' difficile da eseguire ma deve essere effettuata da una persona con un minimo di esperienza in lavori su apparecchiature elettroniche. Se non siete fra questi, chiedete ad un amico di provata esperienza di fare il lavoro per voi. Altrimenti e' possibile che voi causiate danni permanenti al vostro apparato! Comunque e' chiaro che la modifica invalida la garanzia dell'apparato, per cui forse preferite aspettare il termine del periodo di garanzia... L'autore (ed il traduttore) di questa nota non e' in nessun modo responsabile per qualsiasi danno che puo' essere causato al vostro apparato a causa di questa modifica. Lo fate a vostro rischio, e pensateci due volte prima di cominciare ! (Nota del traduttore: Che menagramo questo spagnolo!) -------------------------------------------------------------------------------- Istruzioni per la Modifica -------------------------- 1 - Rimuovere le 4 viti del coperchio INFERIORE. (quello senza altoparlante). 2 - Rimuovere le 4+2 viti della schermatura che copre il modulo P.A. 3 - Rimuovere le 2 viti e togliere la piastrina metallica che copre il foro sotto al cavo coassiale d'antenna. Riavvitare provvisoriamente le 2 viti. 4 - Localizzare il connettore J2 (l'unico bianco grande, vicino al pannello frontale) usato per interfacciare le due schede principali. (16 pins). 5 - Localizzare i pins 1, 2, e 15 di J2. Il pin 1 e' quello piu' vicino al lato del contenitore dell'apparato. Il pin 15 (il penultimo) e' circa a meta' della scheda. Descrizione dei pin: 1 - Entrata modulatore TX UHF. 2 - Massa. 15 - Uscita discriminatore RX UHF. Se non siete sicuri della funzione dei pin, controllare lo schema elettrico (Main B unit, lato sinistro) 6 - Prendete due cavetti schermati SOTTILI, (io ho scelto cavetti a 50 ohms, ma vanno benissimo normali cavetti per AF). Il diametro DEVE essere non piu' di 4 mm. 7 - Unite le due calze dei cavetti e saldatele al pin 2 (massa) sulla parte superiore visibile di J2. Saldate il centrale di un cavetto al pin 1 e il centrale dell'altro al pin 15. La saldatura sulla parte superiore di J2 deve essere fatta con ESTREMA CAUTELA, dato che il supporto di plastica del connettore J2, puo' essere danneggiato seriamente !!! 8 - Far passare i due cavetti lungo la scheda fino al foro vicino al cavo d'antenna, in modo poi da farli attraversare il piccolo foro quadrato nella parte inferiore del coperchio metallico del finale P.A. 9 - Fermare i cavetti, fatti uscire dal foro, con una grossa fascietta di plastica. 10 - Riavvitare le 6 viti al coperchio del finale P.A. 11 - Riavvitare le 4 viti del coperchio inferiore dell'apparato. 12 - Saldare i connettori adatti all'altro lato dei cavetti coassiali. Fine dell'istallazione. ----------------------------------------------------------------------- Nota: Questa modifica riguarda SOLO la parte UHF dell'apparato, quindi la modifica funziona solo per la banda dei 432 MHz. E' stato riscontrato un certo livello di rumore in uscita al discriminatore RX, per cui il led DCD del TNC tende a lampeggiare, ma cio' non pregiudica in nessun modo le prestazioni operative. Giusto come paragone, usando il prg TPK, velocita' della seriale (rs232) a 19200 bds, il ben conosciuto Modem G3RUH ed un TNC standard, in un'ora e' stato stato trasmesso un file di 1.5 Mbytes, alla velocita' di 364 cps. (indicazione del TPK). Andreu EA3CQY @EA3MM Barcellona.Catalogna.Spagna -------------------------------------- traduzione di questa mezza modifica di ÚÄÄ ex ÄÄ¿ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ ³ iw4bkk ³³ PAOLO in Ravenna IW4DGM @IW4CEA.ITA.EU ³Ü ÀÄÄÄÄÄÄÄÄÙÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙÛ ßßßßßßßßßßßßßßßßßßßßßßßßßßßßßßßßßßßßßßßßßßßßßßßßßß