Msg Nr. : 32465 Da : LU7AKC Per : NET9K6@WW Tipo/status : B$ Data/ora : 0815/1302 Dimensione : 4162 Titolo : TS711 & 9600 Bps Bid (Mid) : 12269_LU7AKC TS-711E: Salida de audio del discriminador. Entrada de audio al modulador. Para obtener el audio del discriminador en este equipo, la operaci˘n resulta muy sencilla, pues ya la tenemos en un conector, que soporta el circuito DCS. 1. Localizar el conector 9 en la placa IF UNIT. Esta se encuentra en la parte inferior del equipo. El conector est  pr˘ximo al lateral del equipo. 2. Soldar un hilo (deber  ser apantallado), al pin 1 del conector 9; la malla al pin 2 del conector 9. 3. Llevar el cable apantallado a un conector, o bien aprovechar uno de los pines libres que contiene el conector posterior ACC2 (en mi caso us‚ el pin 2 de este conector). 4. Si accidentalmente se produjera un cortocircuito en este cable, no supondrˇa da¤o alguno, pues en serie tenemos R181 de 47K, lo que nos evitarˇa el deterioro de algŁn componente activo pr˘ximo. 5. Si el nivel de se¤al obtenido fuera insuficiente (no en el caso del modem de G3RUH), podrˇa suprimirse R181, haciendo un puente sobre la propia resistencia. Aquˇ deberˇa extremarse las precauciones de no realizar ningŁn corto en la salida del discriminador. Para introducir la se¤al de Tx en el modulador, directamente al varicap, es necesario realizar lo siguiente: 6. Localizar el conector 2 en la placa IF UNIT. Esta se encuentra en la parte inferior del equipo. El conector est  pr˘ximo al frontal del equipo. 7. Soldar un hilo (deber  ser apantallado), al pin 2 del conector 2; la malla al pin 1 del conector 2. 8. Llevar el cable apantallado a un conector, o bien aprovechar uno de los pines libres que contiene el conector posterior ACC2 (en mi caso us‚ el pin 10 de este conector). Esto es todo lo necesario para obtener buenos resultados a 9600bps. El Łnico ajuste se llevar  a cabo en el nivel de entrada al modulador, actuando sobre el potenci˘metro del modem. IMPORTANTE. Es recomendable desconectar el micr˘fono, pues debe tenerse en cuenta que ‚ste se encuentra en paralelo con el modem, pudiendo captar alguna se¤al no deseable, e interferir al propio modem en su transmisi˘n. Asimismo, cuando se vaya a utilizar el equipo en fonˇa FM, DESCONECTAR el modem, pues se ver  afectada la modulaci˘n por efecto del modem en sˇ mismo. Saludos de Rafa, EA4BPN @ EA4URE.EAM.ESP.EU Msg Nr. : 61168 Da : IW5DAG Per : 9600 @ITA Tipo/status : BF Data/ora : 1104/1338 Dimensione : 3650 Titolo : Modifica 9600 baud per il TS 711 Bid (Mid) : 50167_IK5MEP 9600 BAUD MODIFICATIONS FOR KENWOOD TS-711 & TS-811 +++++++++++++++++++++++++++++++++++++++++++++++++++ The following modifications, while not guaranteed certainly work on my radios: I do not use the ACC 1 Connector on the back panel so I have removed the plastic plug and mounted a five pin DIN socket, although you can use any socket that fits. The requirement for the 9600 baud modem is that transmit audio must modulate the varactor directly, and receive audio must come directly from the discriminator output, both these points are fairly easily accessable; USE GOOD QUALITY AUDIO SCREENED CABLE FOR CONNECTIONS 1. Remove top and bottom covers of TS 711/811. 2. Turn set upside down and locate the PCB marked IF Unit X 48-1400-01 it is the large one on the left facing the rear of the set. Mark, zl1tre RECEIVE AUDIO +++++++++++++ 1. Locate R 173 (3.3K), at the rear left side of the IF Unit PCB alongside a 1 ufd electrolytic capacitor (C 163). The connection to the discriminator output should be made at the junction of R 173, C 159, R 199 and C 163. I did this with a very fine tip soldering iron by soldering to the lead of R 173 nearest to C 163 although it could be soldered under the board if your iron is not small enough. The earth screen I soldered to a lug under the screw head located close by at the corner of the board. 2. Run the cable to the socket on the rear panel and wire as desired. TRANSMIT AUDIO ++++++++++++++ 1. On the same PCB at the front right (facing rear) locate R 11, mounted upright alongside J2 (4 way socket). Connection to the Varactor can be made at Pin 2 of J2 or as I did by carefully filing the lead of R 11 and soldering to it directly. The earth shield I soldered to a lug under the PCB corner mounting screw. This earth is also available at J2 Pin 1. 2. Run the cable to the socket on the rear panel and wire as desired. 3. If you have a scope available, set the tx level to 1.5v P to P at position FMM. If no scope, set the tx level pot on the G3RUH modem to the 11 oclock position and experiment. UoSAT 3 only requires TX Audio from the 711 and RX Audio from the 811 but I would recommend wiring both in each set for future satellites such as RUDAK etc. You will also need to provide a Push to talk connection to your TNC either from the ACC 2 connector or mic socket. I wired from the back of the ACC 2 connector to the DIN socket that I mounted in the spare hole. Good luck, ZL1TRE, Auckland, New Zealand. Msg Nr. : 142601 Da : IW3GRX Per : TEMP Tipo/status : PN Data/ora : 0129/1243 Dimensione : 7914 Bid (Mid) : 11529_IW3GRX Titolo : Modifica 9600 baud per il TS711 **************************************************************************** 9600 BAUD MODIFICATIONS FOR KENWOOD TS-711 & TS-811 +++++++++++++++++++++++++++++++++++++++++++++++++++ The following modifications, while not guaranteed certainly work on my radios: I do not use the ACC 1 Connector on the back panel so I have removed the plastic plug and mounted a five pin DIN socket, although you can use any socket that fits. The requirement for the 9600 baud modem is that transmit audio must modulate the varactor directly, and receive audio must come directly from the discriminator output, both these points are fairly easily accessable; USE GOOD QUALITY AUDIO SCREENED CABLE FOR CONNECTIONS 1. Remove top and bottom covers of TS 711/811. 2. Turn set upside down and locate the PCB marked IF Unit X 48-1400-01 it is the large one on the left facing the rear of the set. Mark, zl1tre RECEIVE AUDIO +++++++++++++ 1. Locate R 173 (3.3K), at the rear left side of the IF Unit PCB alongside a 1 ufd electrolytic capacitor (C 163). The connection to the discriminator output should be made at the junction of R 173, C 159, R 199 and C 163. I did this with a very fine tip soldering iron by soldering to the lead of R 173 nearest to C 163 although it could be soldered under the board if your iron is not small enough. The earth screen I soldered to a lug under the screw head located close by at the corner of the board. 2. Run the cable to the socket on the rear panel and wire as desired. TRANSMIT AUDIO ++++++++++++++ 1. On the same PCB at the front right (facing rear) locate R 11, mounted upright alongside J2 (4 way socket). Connection to the Varactor can be made at Pin 2 of J2 or as I did by carefully filing the lead of R 11 and soldering to it directly. The earth shield I soldered to a lug under the PCB corner mounting screw. This earth is also available at J2 Pin 1. 2. Run the cable to the socket on the rear panel and wire as desired. 3. If you have a scope available, set the tx level to 1.5v P to P at position FMM. If no scope, set the tx level pot on the G3RUH modem to the 11 oclock position and experiment. UoSAT 3 only requires TX Audio from the 711 and RX Audio from the 811 but I would recommend wiring both in each set for future satellites such as RUDAK etc. You will also need to provide a Push to talk connection to your TNC either from the ACC 2 connector or mic socket. I wired from the back of the ACC 2 connector to the DIN socket that I mounted in the spare hole. Good luck, ZL1TRE, Auckland, New Zealand. ****************************************************************************** From: LU7AKC@LU7AKC.#COL.CF.ARG.SOAM To : NET9K6@WW TS-711E: Salida de audio del discriminador. Entrada de audio al modulador. Para obtener el audio del discriminador en este equipo, la operaci˘n resulta muy sencilla, pues ya la tenemos en un conector, que soporta el circuito DCS. 1. Localizar el conector 9 en la placa IF UNIT. Esta se encuentra en la parte inferior del equipo. El conector est  pr˘ximo al lateral del equipo. 2. Soldar un hilo (deber  ser apantallado), al pin 1 del conector 9; la malla al pin 2 del conector 9. 3. Llevar el cable apantallado a un conector, o bien aprovechar uno de los pines libres que contiene el conector posterior ACC2 (en mi caso us‚ el pin 2 de este conector). 4. Si accidentalmente se produjera un cortocircuito en este cable, no supondrˇa da¤o alguno, pues en serie tenemos R181 de 47K, lo que nos evitarˇa el deterioro de algŁn componente activo pr˘ximo. 5. Si el nivel de se¤al obtenido fuera insuficiente (no en el caso del modem de G3RUH), podrˇa suprimirse R181, haciendo un puente sobre la propia resistencia. Aquˇ deberˇa extremarse las precauciones de no realizar ningŁn corto en la salida del discriminador. Para introducir la se¤al de Tx en el modulador, directamente al varicap, es necesario realizar lo siguiente: 6. Localizar el conector 2 en la placa IF UNIT. Esta se encuentra en la parte inferior del equipo. El conector est  pr˘ximo al frontal del equipo. 7. Soldar un hilo (deber  ser apantallado), al pin 2 del conector 2; la malla al pin 1 del conector 2. 8. Llevar el cable apantallado a un conector, o bien aprovechar uno de los pines libres que contiene el conector posterior ACC2 (en mi caso us‚ el pin 10 de este conector). Esto es todo lo necesario para obtener buenos resultados a 9600bps. El Łnico ajuste se llevar  a cabo en el nivel de entrada al modulador, actuando sobre el potenci˘metro del modem. IMPORTANTE. Es recomendable desconectar el micr˘fono, pues debe tenerse en cuenta que ‚ste se encuentra en paralelo con el modem, pudiendo captar alguna se¤al no deseable, e interferir al propio modem en su transmisi˘n. Asimismo, cuando se vaya a utilizar el equipo en fonˇa FM, DESCONECTAR el modem, pues se ver  afectada la modulaci˘n por efecto del modem en sˇ mismo. Saludos de Rafa, EA4BPN @ EA4URE.EAM.ESP.EU ***************************************************************************** KENWOOD TS-711 / TS-811 a 9600 bds Non ho usato il Connettore ACC 1 sul pannello posteriore cosi' ho tolto la copertura di plastica e vi ho montato una presa DIN a cinque poli, comunque potete usare una qualunque presa di qualsiasi tipo. Cosa essenziale per il modem a 9600 baud e' che il TX audio deve modulare il diodo varicup direttamente, ed il RX audio deve arrivare direttamente dalla uscita del discriminatore, entrambi questi punti sono facilmente accessibili; USATE UN CAVETTO AUDIO SCHERMATO DI BUONA QUALITA' PER LE CONNESSIONI. 1. Togliere il coperchio superiore ed inferiore del TS 711/811. 2. Posizionate l'apparato con la parte superiore in basso e localizzate la scheda marcata IF Unit X 48-1400-01 e' quella piu' grande sulla sinistra nella parte dietro del RTX. RX AUDIO 1. Localizzate R 173 (3.3K), a sinistra in fondo alla scheda IF Unit di fianco al condensatore elettrolitico da 1 uF (C 163). Il collegamento all'uscita del discriminatore deve essere fatta alla giunzione di R 173, C 159, R 199 e C 163. Ho usato uno stagno ed un saldatore a punta sottile per saldare il cavetto al terminale di R 173 che e' piu' vicino a C 163, comunque potete fare la modifica dal lato saldature se il vostro saldatore non ha la punta abbastanza sottile. Ho saldato la calza del cavetto ad un punto di massa sotto la vite in un angolo della scheda. 2. Portate il cavetto alla presa del pannello posteriore e saldatelo sul pin che desiderate. TX AUDIO 1. Sulla stessa scheda di fronte a destra localizzate R 11, montata verticale di fianco a J2 (connettore a 4 vie). Il collegamento al Diodo Varicup deve essere fatto al Pin 2 di J2 oppure come ho fatto io, limando delicatamente il terminale di R 11 e saldado il cavetto li' direttamente. Ho saldato la calza a massa sotto la vite in un angolo della scheda. La massa e' anche al Pin 1 di J2. 2. Portate il cavetto alla presa del pannello posteriore e saldatelo sul pin che desiderate. 3. Se siete in possesso di un oscilloscopio, tarate il livello tx a 1.5v PeP in posizione FMM. Senza oscilloscopio, tarate il livello tx del trimmer sul modem G3RUH in posizione "ore 11" e poi provate. Per lavorare UoSAT 3 bisogna che il segnale TX Audio provenga dal 711 ed il RX Audio dal 811 ma vi consiglio di fare la modifica in entrambi gli RTX per futuri satelliti tipo RUDAK ecc. Il segnale PTT e' sul connettore ACC 2 o sul connettore del microfono. Io ho portato il segnale PTT presente nel ACC 2 alla presa DIN a 5 poli che ho montato nel foro libero. Mark ZL1TRE, Auckland, New Zealand ----------------------------------- traduzione di Paolo IW4DGM @IW4CEA *****************************************************************************