Msg Nr. : 32387 Da : LU7AKC Per : NET9K6@WW Tipo/status : B$ Data/ora : 0815/0206 Dimensione : 3002 Titolo : FT211 & 9600 Bps Bid (Mid) : 12248_LU7AKC 9600 BPS with Yaesu FT-211RH The FT-211RH has been shown to be suitable for 9600 baud packet operation. There is no major surgery required just two screened leads are required, one for TX AF the other for RX AF connected as follows: RX AUDIO On the RX IF Unit (sub board F2869104) connect the screened lead inner to the TK10420 IC pin 9 with the outerscreen to pin 15. Caution should be taken to solder these if soldered to the underside of the board. TX AUDIO On the rear of the main PCB a small potentiometer will be seen (peak deviation adjuster). Unsolder the leg nearest to the rear of the set, and connect the inner of the screened TX leads to this point, the outer to the earth plane adjacent to this point. To ensure that the 9600 baud modem is terminated in the required impedance, it is essential that a suitable terminating resistor be placed across the screened lead inner/outer, eg a 560 ohm resister; this may usefully be done at the FT-211RH potentiometer connectioo. No further adjustments need to be made to the radio. On the tested modem a suitable level of 2.5 kHz deviation was achieved with one third rotation clockwise of the modem TX AF level potentiometer. Msg Nr. : 56707 Da : IW4DGM Per : 9600 @ITA Tipo/status : BF Data/ora : 1025/1642 Dimensione : 1251 Titolo : Modifica 9600 baud per FT 211 Bid (Mid) : 8262_IW4CEA Yaesu FT-211RH a 9600bd ----------------------- RX AUDIO: --------- Nella RX "IF UNIT" (sub board F2869104) collegate il centrale di un cavetto schermato (RX) al pin 9 del IC TK10420 e la calza al pin 15. Fate attenzione in questa operazione se saldate il cavetto dal lato saldature. TX AUDIO: --------- Nella parte posteriore della "MAIN UNIT" c'e' un piccolo trimmer (per tarare la deviazione). Dissaldare il terminale piu' vicino alla parte posteriore dell'apparato e collegarlo al centrale di un cavetto schermato (TX) e saldare la calza al piano di massa li' vicino. Per essere sicuri che il modem a 9600 bauds abbia in uscita l'impedenza richiesta, e' essenziale aggiungere una resistenza da 560ohm tra la massa e il centrale del cavetto schermato. Non e' necessario eseguire nessun'altra taratura alla radio. Nel MODEM tarate il livello di deviazione in uscita a 2.5kHz circa un terzo di rotazione del potenziometro TX AF. Phil F1LOU @ON7RC.BT.BEL.EU ------------------------------ traduzione di Paolo IW4DGM @IW4CEA Msg Nr. : 72770 Da : LU7AKC Per : NET9K6@WW Tipo/status : BF Data/ora : 1129/1814 Dimensione : 3283 Titolo : Modifica 9600 baud per l'FT 211 Bid (Mid) : 29972_LU7AKC 9600 BPS with Yaesu FT-211RH The FT-211RH has been shown to be suitable for 9600 baud packet operation. There is no major surgery required just two screened leads are required, one for TX AF the other for RX AF connected as follows: RX AUDIO On the RX IF Unit (sub board F2869104) connect the screened lead inner to the TK10420 IC pin 9 with the outerscreen to pin 15. Caution should be taken to solder these if soldered to the underside of the board. TX AUDIO On the rear of the main PCB a small potentiometer will be seen (peak deviation adjuster). Unsolder the leg nearest to the rear of the set, and connect the inner of the screened TX leads to this point, the outer to the earth plane adjacent to this point. To ensure that the 9600 baud modem is terminated in the required impedance, it is essential that a suitable terminating resistor be placed across the screened lead inner/outer, eg a 560 ohm resister; this may usefully be done at the FT-211RH potentiometer connection. No further adjustments need to be made to the radio. On the tested modem a suitable level of 2.5 kHz deviation was achieved with one third rotation clockwise of the modem TX AF level potentiometer. Msg Nr. : 142560 Da : IW3GRX Per : TEMP Tipo/status : PN Data/ora : 0129/1234 Dimensione : 3653 Bid (Mid) : 11488_IW3GRX Titolo : Modifica 9600 baud per l'FT211 **************************************************************************** Yaesu FT-211RH a 9600bd ----------------------- RX AUDIO: --------- Nella RX "IF UNIT" (sub board F2869104) collegate il centrale di un cavetto schermato (RX) al pin 9 del IC TK10420 e la calza al pin 15. Fate attenzione in questa operazione se saldate il cavetto dal lato saldature. TX AUDIO: --------- Nella parte posteriore della "MAIN UNIT" c'e' un piccolo trimmer (per tarare la deviazione). Dissaldare il terminale piu' vicino alla parte posteriore dell'apparato e collegarlo al centrale di un cavetto schermato (TX) e saldare la calza al piano di massa li' vicino. Per essere sicuri che il modem a 9600 bauds abbia in uscita l'impedenza richiesta, e' essenziale aggiungere una resistenza da 560ohm tra la massa e il centrale del cavetto schermato. Non e' necessario eseguire nessun'altra taratura alla radio. Nel MODEM tarate il livello di deviazione in uscita a 2.5kHz circa un terzo di rotazione del potenziometro TX AF. Phil F1LOU @ON7RC.BT.BEL.EU ------------------------------ traduzione di Paolo IW4DGM @IW4CEA ***************************************************************************** From: LU7AKC@LU7AKC.#COL.CF.ARG.SOAM To : NET9K6@WW 9600 BPS with Yaesu FT-211RH The FT-211RH has been shown to be suitable for 9600 baud packet operation. There is no major surgery required just two screened leads are required, one for TX AF the other for RX AF connected as follows: RX AUDIO On the RX IF Unit (sub board F2869104) connect the screened lead inner to the TK10420 IC pin 9 with the outerscreen to pin 15. Caution should be taken to solder these if soldered to the underside of the board. TX AUDIO On the rear of the main PCB a small potentiometer will be seen (peak deviation adjuster). Unsolder the leg nearest to the rear of the set, and connect the inner of the screened TX leads to this point, the outer to the earth plane adjacent to this point. To ensure that the 9600 baud modem is terminated in the required impedance, it is essential that a suitable terminating resistor be placed across the screened lead inner/outer, eg a 560 ohm resister; this may usefully be done at the FT-211RH potentiometer connection. No further adjustments need to be made to the radio. On the tested modem a suitable level of 2.5 kHz deviation was achieved with one third rotation clockwise of the modem TX AF level potentiometer. *************************************************************************** Yaesu FT-211RH a 9600bd ----------------------- RX AUDIO: --------- Nella RX "IF UNIT" (sub board F2869104) collegate il centrale di un cavetto schermato (RX) al pin 9 del IC TK10420 e la calza al pin 15. Fate attenzione in questa operazione se saldate il cavetto dal lato saldature. TX AUDIO: --------- Nella parte posteriore della "MAIN UNIT" c'e' un piccolo trimmer (per tarare la deviazione). Dissaldare il terminale piu' vicino alla parte posteriore dell'apparato e collegarlo al centrale di un cavetto schermato (TX) e saldare la calza al piano di massa li' vicino. Per essere sicuri che il modem a 9600 bauds abbia in uscita l'impedenza richiesta, e' essenziale aggiungere una resistenza da 560ohm tra la massa e il centrale del cavetto schermato. Non e' necessario eseguire nessun'altra taratura alla radio. Nel MODEM tarate il livello di deviazione in uscita a 2.5kHz circa un terzo di rotazione del potenziometro TX AF. Phil F1LOU @ON7RC.BT.BEL.EU ------------------------------ traduzione di Paolo IW4DGM @IW4CEA ******************************************************************************